This section is from the book "The London Dispensatory", by Anthony Todd Thomson. Also available from Amazon: PDR: Physicians Desk Reference.
The same kind of coating maybe used for glass vessels which are to be exposed to a red heat. The following is the mode of applying it. After kneading the coating material, so as to render it very plastic, let it be spread out on a flat table, and lay the bottom of the retort in the middle of the mass; then turn up the edges of the cake, so as to bring it round the whole of the vessel, pressing it down in every part with the fingers till it apply uniformly and closely. The material may also be applied in the state of thick cream, by dipping the retort repeatedly into it; and drying it after each immersion by turning it before the fire. The different layers of coating may be thus laid on very equally, from the thickness of 1/4 to 1/2 an inch; so as to make the retort resemble a strong earthen retort glazed in the inside; and, as the coating agglutinates in a full red heat, it will form an impenetrable covering which cannot be detached from the glass.
Cements and Lutes are formed of the same materials. They are generally composed of unctuous or resinous substances; mucilaginous or gelatinous substances; or of clay, lime, and similar materials capable of resisting a high degree of heat. a. Unctuous and resinous Lutes.-These should be viscid, plastic, compact, and possess the power of resisting acrid vapours. The following are the best of this class.
1. Melt eight parts of bees' wax with one of turpentine; and according as it is required to be more or less consistent or pliable, add different proportions of any resinous substance. This lute adheres very closely to the glass, is not easily penetrated by acrid vapours, and is very manageable. It cannot bear a heat higher than 1400.1
2. Dissolve spermaceti; and when melted, while it is hot, throw into it bits of caoutchouc. This is an excellent lute where much heat is not required to be employed.
3. Take pure, dry, unbaked clay, finely powdered, beat it for several hours with a heavy iron pestle in a brass mortar, dropping in, slowly, some boiled linseed oil; or some amber varnish, prepared by melting yellow amber in an iron ladle, and mixing it with linseed oil. This lute can sustain a considerable degree of heat, is impenetrable by acids and spirituous liquors, and adheres very strongly to metallic or glass vessels previously rendered perfectly dry. As it softens in some degree, however, by heat, it is necessary to surround the luting with pieces of wet bladder, and to secure the whole by packthread firmly tied round both above and below the joint.1 This lute improves by age. It should be kept in a covered pan in a cool cellar.
1 Lavoisier.
4. Glazier's putty, which is a composition of chalk and drying linseed oil, resembles very much the above lute in its qualities, and may be used as a substitute for it.
5. Take four parts of common resin, one of yellow wax, and one part of fine brickdust; melt the two former together, and when they are melted, stir in the brickdust. This lute adheres with great firmness, and forms also a good cement for stopping cracks in glass vessels.
6. Six parts of clay, one part of iron filings, and enough of linseed oil to form them into a paste, make a good cement for stopping cracks in iron vessels intended to be strongly heated.
7. The following cement is recommended for joining together glass or steel:-"Take of mastich five or six bits as big as peas, and dissolve them in as much alcohol as will render them liquid. In another vessel dissolve as much isinglass (previously soaked in water) in brandy or rum as will make two fluid ounces of a strong glue; warm it, and incorporate with it, by rubbing, two or three small bits of galbanum, or ammoniacum, and the mastich solution. Preserve the mixture in a well-stopped bottle, and gently warm it before use."2
8. A solution of shell lac in alcohol, added to a solution of isinglass in proof spirit, forms a cement that will resist moisture.
b. Mucilaginous and gelatinous Lutes are adapted only for operations which do not require a high temperature, and in which very acrid vapours are not extricated. They are easily applied, are sufficiently adhesive, and can be readily removed by simply moistening them with water.
1. Under this head may be mentioned the simple application of moistened bladder. To render it very adhesive, it should be soaked in tepid water, until it feels clammy to the touch; after which it contracts considerably as it dries, and adheres with a sufficient degree of force.
2. Linseed meal kneaded up with water to a sufficient consistence, and applied pretty thick over the joinings of the vessels, or almond meal treated in the same manner, form very convenient lutes, which dry and become firm in a very short time.
3. Flour paste spread upon slips of moistened paper forms a sufficiently good lute for many purposes.
1 Lavoisier. 2 Aikin't Dictionary of Chymistry,
4. Smear slips of linen on both sides with white of egg; then apply these neatly to the joinings of the vessels; and when they have been applied, shake loosely over them some finely powdered quicklime. This lute dries very quickly, is extremely hard, very cohesive, impervious to water, and impenetrable by most kinds of vapours.
5. Mix powdered plaster of Paris with white of egg, milk, glue, starch, or any mucilage, and apply it immediately.
6. Mix together equal parts of clay and lime, with about one third of flour and white of egg.
7. Mix together equal parts of colcothar and lime, with white of egg.
 
Continue to: